DESERT MOUNTAIN ENERGY SUCCESSFULLY COMPLETES DRILLING OF THIRD HELIUM TEST WELL IN AZ

Vancouver, British Columbia DESERT MOUNTAIN ENERGY CORP.  (the “Company”) (TSX.V: DME, U.S. OTC: DMEHF, Frankfurt: QM01) From the President of the Company.

The Company is pleased to announce that it successfully completed drilling of the previously approved and permitted third well last Tuesday 12/08/20 and open hole logs run and production casing set and cemented into place.  Upon the removal of drilling equipment, the single pit was immediately filled, thereby completing the initial remediation on 12/09/20.  As previously press released the Company had drilled, set and cemented into place the surface casing to protect treatable water on 12/04/20.  The production casing was run and cemented into place on 12/08/20 providing the additional protection to all zones as per the previously approved and permitted well design. 

Drilling operations did not encounter any oil and only found background low btu gas at levels normally associated with the drilling of water wells in this area.  The Company again significantly reduced the amount of water required to drill, with the use of high-pressure air / mist.  This is, to the best of the Company’s information and belief, the same procedure used by the offsetting surface owner to drill their water well last week.  The Company used more surface casing and cement to protect all possible treatable water zones than did the offsetting surface owner.  Even though the Company did not encounter any flows or shows of significant water during drilling through the perceived aquifer as might be normally expected, it still set and cemented protective surface casing in accordance with the approved permit.  The well logs also indicated the placement of the well correlated with Company plans to have the drilling intercept the highest porosity zones, again precluding the need for fracking.  The Company has previously stated its goal is to apply geology and geophysics to successfully select drilling locations to remove the need for large fracks similar to what has been routinely done to produce oil from tight formations. 

The open hole well logs indicated the Company encountered multiple prospective helium bearing zones.  Resistivities in the three prospective helium bearing zones range from 48 ohms to a high in excess of 120 ohms.  Excellent porosities demonstrated direct correlation to the prospective helium bearing zones with the thickest probable helium bearing zone being 59’ thick.      

The successful drilling of the third well some 74 miles away from the first two wells (the results of which were previously announced in June and July 2020) clearly demonstrates the Company’s geologic modeling plans in reference as to the basic required trap mechanisms for commercial helium production in NE Arizona.  Per Penwell Publishing data the average success rate on wildcat exploration wells for major companies has dropped from a high of 30.3% in 1997 with the average successful drilling rate for independents to be off a high of 17.6% in the same time period.  Desert Mountain Energy Corp’s corporate strategy to repeatedly find possible helium producing areas is clearly proven.   

About Desert Mountain Energy

Desert Mountain Energy Corp. is a publicly traded exploration and resource company focused on the discovery and development of rare earth gas fields in the US.  The Company is primarily looking for elements deemed critical to the green energy and high technology industries.

We seek safe harbor

“Robert Rohlfing”
Robert Rohlfing
Chairman & CEO

For more information, contact:

Don Mosher, Vice President of Finance

(604) 617-5448

E-mail: [email protected]

Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in polices of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release. The statements made in this press release may contain certain forward-looking statements that involve a number of risks and uncertainties.  Actual events or results may differ from the Company’s expectations.                                                                                                                

DESERT MOUNTAIN ENERGY COMMENCES DRILLING THE THIRD WELL OF ITS HELIUM PROGRAM IN ARIZONA’S HOLBROOK BASIN

Vancouver, British Columbia DESERT MOUNTAIN ENERGY CORP.  (the “Company”) (TSX.V: DME, U.S. OTC: DMEHF, Frankfurt: QM01) From the President of the Company.

Vancouver, British Columbia — Desert Mountain Energy Corp. (the “Company”) (TSX. V:DME) is pleased to announce that it has commenced drilling its third well in Arizona. DME well # State 26-1.

The well is anticipated to be drilled to a total depth (TD) of approximately 2,000 feet. This well is located approximately 70 miles west of the first two wells and is intended to prove up a number of significant geological structures in the western portion of the basin. The Company’s technical team has identified three potential target zones in this well. Surface casing has been set and cemented into place and after sufficient curing time for the cement, drilling to planned TD is ongoing.

After drilling this well to planned TD and a decision has been made to set & cement production casing, a completion rig will be brought in to complete the well, perforate and test specific zones. That testing if undertaken will include a full gas composition test completed by an independent third party.

About Desert Mountain Energy

Desert Mountain Energy Corp. is a publicly traded exploration and resource company focused on the discovery and development of rare earth gas fields in the US.  The Company is primarily looking for elements deemed critical to the green energy and high technology industries.

We seek safe harbor

“Robert Rohlfing”
Robert Rohlfing
Chairman & CEO

For more information, contact:

Don Mosher, Vice President of Finance

(604) 617-5448

E-mail: [email protected]

Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in polices of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release. The statements made in this press release may contain certain forward-looking statements that involve a number of risks and uncertainties.  Actual events or results may differ from the Company’s expectations.